[time-nuts] Question and help with LPRO-101

Ian Sheffield ian.sheffield1 at tesco.net
Mon Oct 20 19:31:56 UTC 2008


Many thanks Don,

The only thing I want to look at (and tweek) is the C Field adjustment. For 
some reason I can't seem to be able to turn the pot properly through the 
small hole in the case, so I will have a look to see if anything is 
mechanically mis-aligned.

I promise I won't tweek anything else!

Cheers,

Ian.

----- Original Message ----- 
From: "Don @ True-Cal" <true-cal at swbell.net>
To: "Discussion of precise time and frequency measurement" 
<time-nuts at febo.com>
Sent: Monday, October 20, 2008 7:57 PM
Subject: Re: [time-nuts] Question and help with LPRO-101


Ian,

No problem, more discussion - the better.

Unscrew the two hex standoffs on either side on the connector, pull the 
10-pin feed-through out of the internal connector. Note the position of the 
grounded pins vs. the capacitive bypass feedthrough pins. This will free up 
the metal cover to "snap" off of the base plate. A very small screwdriver 
can be used in the small slots at each of the four coners to pry the box 
cover free from the base plate.

Caution, here is where a little will-power is needed to resist tuning the 
several adjustments for "better performance".

Have fun,
Don


----- Original Message ----
From: Ian Sheffield <ian.sheffield1 at tesco.net>
To: Discussion of precise time and frequency measurement 
<time-nuts at febo.com>
Sent: Monday, October 20, 2008 1:34:01 PM
Subject: Re: [time-nuts] Question and help with LPRO-101

Hello Don,

Sorry to hijack your question, but how do you get inside an LPRO-101? Does
the case just spring off?

Thanks,

Ian.


----- Original Message ----- 
From: "Don @ True-Cal" <true-cal at swbell.net>
To: <time-nuts at febo.com>
Sent: Monday, October 20, 2008 7:05 PM
Subject: [time-nuts] Question and help with LPRO-101


Hello,

Can anyone guide me or give me a link to internal settings on the Efratom
LPRO-101 Rb oscillator. I have the User's and Integration Guide but I am
looking for more detailed information on any optional settings that may be
available from the many inside jumpers and/or hidden connectors.
Specifically, all of the units I have provide a 10MHz sine wave output and I
am wanting a 1PPS output on one of the units. I believe there are LPROs that
provide a 1PPS output but not sure if they are a different part number unit
with different electronics or just different jumper options inside. I scoped
the hidden connector J6 but no 1PPS signal.

There is a 9-pair J8 jumper block with 2 jumpers and a 7-pair J8 with one
jumper and a 2-pair J1 with no jumper. There is also a connector block J9
and a 3-pair J10 but they are back by the Rb lamp/cavity with analog signals
on some probably for initial test/calibration.

My units are Cage Code 55761, Part Number 102500-001

Thanks...
Don
_______________________________________________
time-nuts mailing list -- time-nuts at febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.


--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - http://www.avg.com
Version: 8.0.173 / Virus Database: 270.8.1/1734 - Release Date: 10/20/2008
07:25


_______________________________________________
time-nuts mailing list -- time-nuts at febo.com
To unsubscribe, go to 
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts at febo.com
To unsubscribe, go to 
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.


--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - http://www.avg.com
Version: 8.0.173 / Virus Database: 270.8.1/1734 - Release Date: 10/20/2008 
07:25




More information about the time-nuts mailing list