[time-nuts] 1" 14 tpi UNS die

Robert Atkinson robert8rpi at yahoo.co.uk
Tue Jul 7 20:13:39 UTC 2009


Try Shakespeare 4705
 http://shakespeare-marine.com/mountshow.asp?findmount=4705
1" pipe slip-over to 1"-14tpi

Photo attached
Robert G8RPI

--- On Tue, 7/7/09, Arnold Tibus <Arnold.Tibus at gmx.de> wrote:

> From: Arnold Tibus <Arnold.Tibus at gmx.de>
> Subject: Re: [time-nuts] 1" 14 tpi UNS die
> To: "Discussion of precise time and frequency measurement" <time-nuts at febo.com>
> Date: Tuesday, 7 July, 2009, 7:10 PM
> Nigel and the group,
> 
> this very useful adapter is what is needed and I am looking
> for as well.
> 
> regards
> Arnold
> 
> On Tue, 7 Jul 2009 13:53:55 EDT, GandalfG8 at aol.com
> wrote:
> 
> > 
> >In a message dated 07/07/2009 18:43:55 GMT Daylight
> Time,  
> >Arnold.Tibus at gmx.de
> writes:
> 
> >I have  the same problem with several GPS
> antennas, a Quadrifilar from 
> >Raytheon,  
> >Irvine 2640NW with mounting base, HP 58532A with
> mounting base, 
> >HP  58504Ac. etc. Some complete boxes from HP do
> contain an adapter.
> >So this  thread is definitively a kind of
> standard. The thread is fully
> >cylindrical,  all the plumbers tubes do use
> conical threads which are not 
> >compatible.  Very difficult to find proper
> solution in the metrical Europe.
> >If I would  find a source of that HP-adapters I
> would buy 4 units.
> >I did not check for  the correct naming of this
> thread though.
> 
> 
> >---------------
> >As commented previously, this is a common fitting and
> fairly standard  for 
> >GPS antennas and some other antenna kit, especially in
> a marine  environment.
> > 
> >A variety of adaptors is available from marine
> suppliers ranging from  
> >expensive stainless steel fittings to much cheaper
> plastic, they are also  
> >regularly listed on Ebay.
> > 
> >However, there doesn't seem to be anything readilly
> available  which has a 
> >collar to sit over a plain pipe, which I suspect
> might  meet David's needs.
> >They are widely available with a flange fitting, for
> mounting to flat  
> >surfaces, or rail fittings to attach to horizontal deck
> rails, but perhaps a  
> >trawl through some of the marine suppliers might throw
> up something else that  
> >could do the job without the need for threading the end
> of the pipe.
> > 
> >regards
> > 
> >Nigel
> >GM8PZR
> >_______________________________________________
> >time-nuts mailing list -- time-nuts at febo.com
> >To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> >and follow the instructions there.
> 
> 
> 
> -----Inline Attachment Follows-----
> 
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.


      
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 4705.jpg
Type: image/pjpeg
Size: 12691 bytes
Desc: not available
URL: <http://www.febo.com/pipermail/time-nuts/attachments/20090707/e28af646/attachment-0001.bin>


More information about the time-nuts mailing list