[time-nuts] Pls help identify this board

Pete Lancashire pete at petelancashire.com
Sat Nov 19 18:23:47 UTC 2011


http://forums.ni.com/

On Sat, Nov 19, 2011 at 7:28 AM, Chuck Forsberg WA7KGX N2469R
<caf at omen.com> wrote:
> I found some working diagnostics in ate7.zip on their FTP site.
> The following works in gpib.conf.  Notice no _accel in the board type.
> Apparently the "turbo" inscription on one of the ASICS is a bit fanciful.
> DMA doesn't work but is not needed to read the counter.
>
> interface {
>    minor = 0    /* board index, minor = 0 uses /dev/gpib0 */
>    board_type = "ni_nec_isa"
>    name = "at"
>    pad = 0    /* primary address of interface             */
>    sad = 0    /* secondary address of interface           */
>    timeout = T3s    /* timeout for commands */
>
>    eos = 0x0a    /* EOS Byte, 0xa is newline and 0xd is carriage return */
>    set-reos = yes    /* Terminate read if EOS */
>    set-bin = no    /* Compare EOS 8-bit */
>    set-xeos = no    /* Assert EOI whenever EOS byte is sent */
>    set-eot = yes    /* Assert EOI with last byte on writes */
>
> /* settings for boards that lack plug-n-play capability */
>    base = 0x2c0    /* Base io ADDRESS                  */
>    irq  = 7    /* Interrupt request level */
>    dma  = 0    /* DMA channel (zero disables)      */
>
>    master = yes    /* interface board is system controller */
> }
>
>
> On 11/19/2011 07:05 AM, paul swed wrote:
>>
>> Is that an isa board as I recall?
>> I seem to remember the 7210 chip from ages ago.
>> Regards
>> Paul.
>>
>> On Sat, Nov 19, 2011 at 9:48 AM, J. Forster<jfor at quikus.com>  wrote:
>>
>>> Call or email National support. They were very good, last seen. Try and
>>> get the diagnostics.
>>>
>>> -John
>>>
>>> ===========
>>>
>>>
>>>> I got a National Instruments AT-GPIB board that I can't
>>>> make work.  It has a NEC 7210 in the upper right hand
>>>> corner of the board.  It also has a National Instruments
>>>> 700454-01 A "TURBO 488" chip in a socket.
>>>> It has a ASSY180625-01  REV C2  a/n 3748.
>>>>
>>>> I can't find gpib.conf parameters to make it it work.
>>>>
>>>> The software does work with a PCIIa board.
>>>>
>>>> --
>>>> Chuck Forsberg WA7KGX N2469R     caf at omen.com   www.omen.com
>>>> Developer of Industrial ZMODEM(Tm) for Embedded Applications
>>>>    Omen Technology Inc      "The High Reliability Software"
>>>> 10255 NW Old Cornelius Pass Portland OR 97231   503-614-0430
>>>>
>>>>
>>>> _______________________________________________
>>>> time-nuts mailing list -- time-nuts at febo.com
>>>> To unsubscribe, go to
>>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>>> and follow the instructions there.
>>>>
>>>>
>>>
>>>
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to
>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to
>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>>
>
> --
> Chuck Forsberg WA7KGX N2469R     caf at omen.com   www.omen.com
> Developer of Industrial ZMODEM(Tm) for Embedded Applications
>  Omen Technology Inc      "The High Reliability Software"
> 10255 NW Old Cornelius Pass Portland OR 97231   503-614-0430
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>



More information about the time-nuts mailing list