[time-nuts] Isotemp OCXO trimpot question...
Bob Camp
lists at rtty.us
Wed Aug 29 00:44:08 UTC 2012
Hi
I wouldn't go to crazy digging up a 10K pot. I suspect that anything in the 10K to 50K range will work ok.
Bob
On Aug 28, 2012, at 8:24 PM, jmfranke <jmfranke at cox.net> wrote:
> Now I need to find a 10 KW potentiometer!
>
> John
>
> --------------------------------------------------
> From: "Jerry" <jsternmd at att.net>
> Sent: Monday, August 27, 2012 8:10 PM
> To: "'Discussion of precise time and frequency measurement'" <time-nuts at febo.com>
> Subject: Re: [time-nuts] Isotemp OCXO trimpot question...
>
>> I don't know if the list allows attachments but I tried to attach to this
>> email a datasheet for a very similar Isotemp 10Mhz OCXO (Model OCXO134-10;
>> PN 6624.00002). Just in case the attachment doesn't come thru here is the
>> relevant section.
>>
>> I am not certain whether the pins are the same as your model but I believe
>> all the Isotemp OCXO have same arrangement:
>>
>> 3. ELECTRICAL FREQUENCY ADJUSTMENT
>> 3.1. Range > ±0.45 PPM
>> < ±1.2 PPM (At time of shipment) (Referenced
>> to nominal frequency)
>> 3.2. Control 0 VDC to Vref (0 VDC to +8 VDC ) or a 10 kW
>> potentiometer connected between pins 2 and 4 with wiper connected to pin 3.
>> 3.3. Slope Positive
>> 3.4. Center Vref/2 ±10% of Vref (+4 VDC to +0.8 VDC)
>>
>>
>> Jerry
>>
>>
>> -----Original Message-----
>> From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] On
>> Behalf Of Azelio Boriani
>> Sent: Monday, August 27, 2012 6:57 PM
>> To: Discussion of precise time and frequency measurement
>> Subject: Re: [time-nuts] Isotemp OCXO trimpot question...
>>
>> If there is no datasheet to refer to then the usual value is between 10K and
>> 20K.
>> 10K is the most common value for 5V or 8V Vref. The OCXO should provide the
>> Vref output pin to connect one side of the pot, the other to GND, for a GND
>> referenced EFC. Your mileage may vary but, without a datasheet, it is the
>> best starting point.
>>
>> On Mon, Aug 27, 2012 at 11:26 PM, Bud Patten
>> <bud.patten at frontiernet.net>wrote:
>>
>>> I have an Isotemp OCXO (674-0010-000) an am wondering what is the
>>> recommended value for the frequency trim pot?
>>>
>>> Bud
>>> W0LCP
>>>
>>> Time is only there to prevent
>>> everything from happening at once.
>>>
>>> Einstein
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>>
>
>
>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
More information about the time-nuts
mailing list