[time-nuts] Fwd: Re: Contact: Jupiter GPS questions

Keenan Tims keenan.tims at gmail.com
Fri Oct 19 14:27:39 UTC 2012


There is an MSP430 port of GCC that works fine, and mspdebug is able to
write the code to the chip via the programming hardware that comes on
the Launchpad boards. TI also provides several free IDEs with code size
limits, if you prefer that route. Definitely not as easy for a beginner
as an Arduino - the chips are more complicated and the documentation a
bit more arcane - but there's still a good community around them and
decent tools available for free. There's also the ST 'DISCOVERY' series.
Much more powerful chips, on a board, with a USB programmer still around
the $10 mark, but coding for ARM is again another step up the difficulty
ladder.

Plenty of options that will work to send a few bytes of serial at power
on, but for a complete beginner I'd say just spend the extra money and
get an Arduino or chipKit because they're super easy to get going on.
Such a project should be a couple hours of work, even for a beginner.
Just figuring out how to set up the compiler and linker properly and
init the chip can be a week's work for a newbie on ARM...

The other option, of course, is to modify whatever you're using for APRS
to send the string. I don't think you mentioned which tracker / software
you intend to use, but it maybe be possible.

Keenan VE7XEN

On 2012-10-19 6:45 AM, shalimr9 at gmail.com wrote:
> Hi TJ,
>
> The Jupiter receivers I have are the standard part, and like you I have found detailed design info hard to come by.
>
> All I can suggest for your issue is to use a small microcontroller to send the commands to the receiver at power up, then go to sleep until the next power cycle.
>
> I have been using Silabs' Toolsticks for hacks of that nature. There is an example of such hack with my GPS monitor project.
>
> You do not need to buy any software (the Silabs IDE is free, and you can use either the free and limited Keil demo C compiler, or the free and unlimited SDCC C compiler.)
>
> I have C code for talking to a Maxim DS1629 RTC, and you could use my GPS monitor project as a starting point.
> Even though the GPS monitor only listens to the Thunderbolt, there is software support for sending messages as well in the source code.
>
> The F330 Toolstick is about $10 and the programmer is about $20. Alternately, TI has cheaper kits for their MPS430, but the C compilers are not free, and writing in assembly is not my idea of fun.
>
> I am sure those familiar with the PICs will suggest their favorite solution as well.
>
> Didier
>
> PS: I take the liberty of sending this to the time-nuts list, as there may be other people interested to chime in.
>
> Sent from my Droid Razr 4G LTE wireless tracker using MailDroid.
>
>
>
> -----Original Message-----
> From: TJ Fiel <zulutime at yahoo.com>
> To: didier_juges at yahoo.com
> Sent: Thu, 18 Oct 2012 3:41 PM
> Subject: Contact: Jupiter GPS questions
>
> Name: TJ Fiel
>
> Email: zulutime at yahoo.com
>
> Subject: Jupiter GPS questions
>
> Message: Hello KO4BB,
>
> Many thanks for making so many resources available through your
> website.  I'd never seen Labmon 7 before and it cured several
> problems with previous versions.
>
> I'm attempting to use a Jupiter serial GPS receiver with APRS.  This
> is an OEM version made for Etak/Sony about 1999, p.n. TU40-D310-011. 
> It uses the Rockwell Scorpio DSP (11577-11) but implements few
> features.  I've never found a datasheet or even a pinout for this
> chip.  Conexant stopped producing this chip about ten years ago and
> now they don't appear to answer their phones.  Apparently they never
> released chip level data to the public for this DSP, only for
> built-up GPS modules.
>
> My biggest issues are automatically forcing NMEA out at startup and
> possibly adding an RTC.  Any insights you can give will be greatly
> appreciated.
>
> Best wishes and thanks,
> TJ Fiel
>
> IP: 71.34.158.74
> HOST: 71-34-158-74.clsp.qwest.net
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.




More information about the time-nuts mailing list