[time-nuts] Measuring Phase difference between different GPSDO

Bob Camp lists at rtty.us
Fri May 3 11:09:10 EDT 2013


Hi

Grab an old garage sale category PC, blow the dust out of it and fire up the
GPIB. Once it's all working next steps:

Check out TimeLab and EZGpib. Both are pretty good at talking to "stuff".
TimeLab does support the 5370, not sure about the other programs.

If you have two GPSDO's with pps outputs, feed one into each channel on the
5370. Put it in start / stop mode and you should see the difference between
the two. Since they can be either ahead or behind each other things can get
a little messy. 

Next, go to the software that runs your GPSDO and look for the "cable delay"
setting. Adjust it on one GPSDO so it's always early (or late) by a couple
hundred nanoseconds. Now fiddle the cables to the counter so it reads a
couple hundred nanoseconds and not almost a full second :).

At this point you are reading frequency to a very high resolution. The
GPSDO's likely are only good to a couple of nanoseconds at 1 second. The
counter should be good to ~0.02 ns.

Run like this for a few minutes and see what you get.

-----------

Now that you have conquered that approach it's time to tear it all apart and
try something new.

Feed the 1 pps into one input of the counter (just like before). Hit the
other input with 10 MHz. You now will get a reading in the 0 to 100 ns
range. Each time a cycle slips past the 1 pps the reading will skip from
99.xxx to 0.xxx ns. That's called a phase wrap around. Click the appropriate
boxes on which ever software you are running and it should take care of the
wrap.

--------

Either way the software should show you frequency, and frequency stability. 

Bob


-----Original Message-----
From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] On
Behalf Of Mark C. Stephens
Sent: Friday, May 03, 2013 10:07 AM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] Measuring Phase diference between different GPSDO

Hey Bob, I was thinking the exact same thought, and I found a NI PCI-GPIB
card in a PC with a dead HDD.
These appear to be 5V PCI cards so I can't stick it in a nice rack mount
server with raid as they all seem to be 3.3v PCI.
So I put a new HDD in the PC and I have stuck WinXP on it.
Now I am awaiting further orders!  ;)

mark

-----Original Message-----
From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] On
Behalf Of Bob Camp
Sent: Friday, 3 May 2013 9:21 PM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] Measuring Phase diference between different GPSDO

Hi

If you have a pile of GPIB cables, you may also have a GPIB card on a PC.
You will have a lot more luck finding free software to read and log the data
from the 5370 than from the 3575. As mentioned before, the 5370 will be much
more accurate / higher resolution in this application. 

Bob

On May 3, 2013, at 12:28 AM, Mark C. Stephens <marks at non-stop.com.au> wrote:

> According to http://www.realhamradio.com/z3801a-turning-point.htm they use
a HP 3575A phase meter to perform the measurement.
> Or perhaps I have misinterpreted the whole thing?
> 
> 
> I do have a temperature controlled workshop that is always 24 degrees so
hopefully thermal drift won't be too much of an issue.
> 
> 
> mark
> 
> -----Original Message-----
> From: time-nuts-bounces at febo.com [mailto:time-nuts-bounces at febo.com] 
> On Behalf Of lists at lazygranch.com
> Sent: Friday, 3 May 2013 12:12 PM
> To: Discussion of precise time and frequency measurement
> Subject: Re: [time-nuts] Measuring Phase diference between different 
> GPSDO
> 
> Meditating on this a bit, I assume in a strict sense, you can only
consider GPSDOs phase locked if they are disciplined from the same GPS.
> 
> Or is this being pedantic?
> 
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to 
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
> 
> 
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to 
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.

_______________________________________________
time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.


_______________________________________________
time-nuts mailing list -- time-nuts at febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.




More information about the time-nuts mailing list