[time-nuts] Low cost SDR suitable for phase noise measurement?

Bob Camp kb8tq at n1k.org
Thu Aug 11 22:41:16 EDT 2016


Hi

In a DMTD (or in the equally useful single mixer setup) the advantage for frequency measurement 
comes from the downconversion process. The further you downconvert (10 Hz vs 100 Hz) the
greater your potential resolution. The design approach is to push the beat note as low as you 
can without running into other limits. With conventional setups that is in the 1 to 10 Hz range. 

If you want to fiddle a bit, there is no particular reason why you must use a limiter after the 
mixer. An ADC after the mixer could be used to process the audio and estimate it’s frequency. 
The same sort of ADC setup might give you some phase noise data. 

The gotcha with all this is that a single mixer / quadrature approach will give you *much* better
phase noise data than a single or dual mixer setup. If phase noise is the objective, there is no
reason to run the mixer setup as a DMTD. With a DMTD you digitize the carrier (audio beat note)
and then try to dig down 195 db to get to the phase noise. With a quadrature approach you null out
the carrier. Then all you have to deal with is the noise. 

Bob


> On Aug 11, 2016, at 5:15 PM, Bob Stewart <bob at evoria.net> wrote:
> 
> Hi Bob,
> If I understand the question correctly, yes.  The DMTDs that I've encountered so far use a zero-crossing detector and a TIC.  I wanted to build sort of a hybrid system that has a DMTD front end and an SDR back end.  It seemed to me that that would be sort of half way between a DMTD and a Timepod.  But whereas the Timepod digitizes 4 RF signals, this would digitize 2 audio signals.  It may be that it suffers all the disadvantages of both and has the advantages of neither, but I thought I'd build it and see where it leads.
> As to the 1 to 10 Hz range, doesn't that depend on the heterodyne frequency you choose?  I mean, you don't have to use a 10 Hz offset, do you?
> 
> Bob
>  -----------------------------------------------------------------
> AE6RV.com
> 
> GFS GPSDO list:
> groups.yahoo.com/neo/groups/GFS-GPSDOs/info
> 
>      From: Bob Camp <kb8tq at n1k.org>
> To: Discussion of precise time and frequency measurement <time-nuts at febo.com> 
> Sent: Thursday, August 11, 2016 3:13 PM
> Subject: Re: [time-nuts] Low cost SDR suitable for phase noise measurement?
> 
> Hi
> 
> Just to clarify:
> 
> You are looking for a way to digitize the output(s) of the mixer(s) in a DMTD. The 
> “target signal” is in the 1 to 10 Hz range.
> 
> Is that correct or are you looking for something to use instead of a DMTD? 
> 
> Bob
> 
> 
>> On Aug 11, 2016, at 3:29 PM, Bob Stewart <bob at evoria.net> wrote:
>> 
>> Hi Brooke,
>> It looks like I've asked a question poorly, yet again.  So, let me try again.  I have this idea of combining a DMTD with an SDR.  So, said that way, it looks like what I really need is a 2-channel audio SDR.  And having said that, maybe what I'm looking for is an external USB sound card.  Those I can find.  I can probably even figure out how to convert them to DC and supply them with a disciplined oscillator, if needed.
>> 
>> Bob
>>   -----------------------------------------------------------------
>> AE6RV.com
>> 
>> GFS GPSDO list:
>> groups.yahoo.com/neo/groups/GFS-GPSDOs/info
>> 
>>       From: Brooke Clarke <brooke at pacific.net>
>> To: Discussion of precise time and frequency measurement <time-nuts at febo.com> 
>> Sent: Thursday, August 11, 2016 1:36 PM
>> Subject: Re: [time-nuts] Low cost SDR suitable for phase noise measurement?
>> 
>> Hi Bob:
>> 
>> The SDR-IQ has a lower frequency limit of 500 Hz.
>> http://www.prc68.com/I/Bats.shtml#SDRIQ
>> 
>> There is a mod that replaces the on board 66 MHz oscillator with one locked to 10 MHz.
>> 
>> -- 
>> Have Fun,
>> 
>> Brooke Clarke, N6GCE
>> http://www.PRC68.com
>> http://www.end2partygovernment.com/2012Issues.html
>> The lesser of evils is still evil.
>> 
>> -------- Original Message --------
>>> A number of posts have appeared about Zynq SDRs on the "Shera revisited" thread.  So, I'd like to ask the more general question: Are there any low cost SDRs that are suitable for measuring phase noise when coupled with a DMTD?  I believe what I'm looking for is something with enough bits to work in the audio range down to DC.  Yes, I could use a modified sound card, but I'm really looking for something not sound card related.  My thought was to use a DMTD with a heterodyne frequency of maybe 5KHz.
>>> 
>>> Bob -----------------------------------------------------------------
>>> AE6RV.com
>>> 
>>> GFS GPSDO list:
>>> groups.yahoo.com/neo/groups/GFS-GPSDOs/info
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>> 
>> 
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
>> 
>> 
>> 
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
> 
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
> 
> 
> 
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.



More information about the time-nuts mailing list