[time-nuts] For those that insist on using switching power supplies

[Cube Central]

Nick, thanks for your detailed reply.  Would you happen to have a photo of the "spring looking things?"  I am not entirely sure I have one of those included with the kit that came with the scope.
What size of capacitor would you suggest?
I happen to have the exact same dummy load that you do.  I have added on a fan for higher current/longer use.

Thanks for the help, I look forward to trying out some of the measurements that I've seen posted elsewhere ( such as this link: http://www.righto.com/2012/10/a-dozen-usb-chargers-in-lab-apple-is.html ) 

Cheers!

	-Randal R.
		(at CubeCentral)

-----Original Message-----
From: time-nuts [mailto:time-nuts-bounces at febo.com] On Behalf Of Nick Sayer via time-nuts
Sent: Friday, 14 October, 2016 12:17
To: Discussion of precise time and frequency measurement <time-nuts at febo.com>
Subject: Re: [time-nuts] For those that insist on using switching power supplies

Set your scope for AC coupling. Set your scope probe for 1x rather than 10x. Use the absolutely shortest scope grounding you can. That’s what those spring looking things that came with it are for. I typically use the spring gizmo and probe on an SMD cap. The ground wire with an alligator clip will just pick up far more noise than you’ll be measuring. This is how I was able to measure the noise and ripple of the SC189Z switcher feeding the OCXO in my GPSDO. I got measurements of ~4 mV P-P that way. Be careful you don’t get the probe and ground reversed - your scope won’t likely have an isolated ground from your DUT and that would therefore be bad.

You’re going to want to check the supply’s performance under load. For that, you’ll may want to get yourself a dummy load. I got one from Tindie for testing my Pi Power design: https://www.tindie.com/products/arachnidlabs/reload-2/



> On Oct 14, 2016, at 11:00 AM, Cube Central <cubecentral at gmail.com> wrote:
> 
> How would one go about testing power supplies and seeing how noisy they are?  I have the standard suite of tools, an oscilloscope and a little (dangerous) know-how.  I am just not sure what to look for or how to safely hook it up to test.
> 
> Thanks in advance for any tips!  
> 
> 	-Randal R.
> 		(at CubeCentral)
> 
> -----Original Message-----
> From: time-nuts [mailto:time-nuts-bounces at febo.com] On Behalf Of Chris 
> Albertson
> Sent: Friday, 14 October, 2016 02:29
> To: Discussion of precise time and frequency measurement 
> <time-nuts at febo.com>
> Subject: Re: [time-nuts] For those that insist on using switching 
> power supplies
> 
> On Thu, Oct 13, 2016 at 6:05 AM, Van Horn, David <david.vanhorn at backcountryaccess.com> wrote:
>> To be fair here, phone chargers have almost no requirement to be quiet other than conducted and radiated emissions limits.
>> It's charging a battery.
> 
> Not only that but,  the 5 volts comping out of the larger is almost certainly the input to another DC/DC power supply and NOT used directly.
> You can't charge a Lithium battery with the 5 volts the charger outputs.
> 
> If you don't know about LiPo batteries, they need a constant current power source and then as they get close to charged the charger switches to constant voltage (VERY roughly) at about 4V per cell.
> 
> I have a project right here on my desk as I type.  I'm using the output of a generic USB hub.  The circuit is  a cap from 5V to GND and
> then a low dropout regulator to get 3.3 volts.    I don't care to much
> if there is huge ripple on the 5.0 volts coming in as long as it stays above the LDO limit.
> 
> Also it looks like they tested the USB chargers with no load.  A typical load might have a say, 0.01uf cap to short the noise to ground.  So in use the power might be better?
> 
> It was no surprise the counterfeit chargers were horrible.  The manufacturers are by definition of "counterfeit" being dishonest slim balls. Why would he care about anything other then that he can fool
> some people into buying his product.   There are third party chargers
> that are not trying to copy a well known brand, these are usually much 
> better
> 
> 
> --
> 
> Chris Albertson
> Redondo Beach, California
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to 
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
> 
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to 
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.

_______________________________________________
time-nuts mailing list -- time-nuts at febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.