[time-nuts] Rakon HSO-14
Bruce Griffiths
bruce.griffiths at xtra.co.nz
Sat Feb 3 22:39:16 EST 2018
There is abrasive entrained in the fluid stream. Operation is in the ductile grinding regime so fluid pressures are around 6 bar or so, way below that used in abrasive water jet cutting.
It has been used to machine/polish crystal quartz waveplates and to machine/polish the surface of silicon wafers before uses for MEMS fabrication. Its even been used to carve channels in silicon wafers in such applications.
Bruce
> On 04 February 2018 at 15:26 Bob kb8tq <kb8tq at n1k.org> wrote:
>
> Hi
>
> Unfortunately ( at the rates you must use) the “blast it with a fire hose” approach
> is not very fast…..
>
> Bob
>
>
> > > On Feb 3, 2018, at 8:15 PM, Bruce Griffiths <bruce.griffiths at xtra.co.nz mailto:bruce.griffiths at xtra.co.nz > wrote:
> >
> >
> > Fluid jet polishing perhaps?
> >
> > At least on fused quartz and optical glass there is no associated subsurface damage.
> >
> > Bruce
> >
> > > > >
> > > On 04 February 2018 at 14:05 Bob kb8tq <kb8tq at n1k.org mailto:kb8tq at n1k.org > wrote:
> > >
> > > Hi
> > >
> > > If you try “normal” machining techniques on a resonator, you are very
> > > likely to create micro cracks in the material. Those are *really* bad for
> > > aging and a few other issues ….. Much of the normal production flow of the
> > > quartz is designed to keep the processes like sawing far enough away
> > > from the “end product” that more gentle techniques can be used to remove
> > > the (possibly) damaged material.
> > >
> > > Since the slots are pretty darn small, there isn’t a lot of room for this and that
> > > to be done when making them. There may well be better ways to do the
> > > work today than back 20 or 30 years ago. It would still take a *lot* of effort
> > > to validate a process.
> > >
> > > Bob
> > >
> > > > > > >
> > > > On Feb 3, 2018, at 7:24 PM, Poul-Henning Kamp <phk at phk.freebsd.dk mailto:phk at phk.freebsd.dk > wrote:
> > > >
> > > > --------
> > > > In message <0f9a9acc-4cdf-780f-e633-6162622641e3 at earthlink.net mailto:0f9a9acc-4cdf-780f-e633-6162622641e3 at earthlink.net >, jimlux writes:
> > > >
> > > > > > > > >
> > > > > > > > > > >
> > > > > > [1] Surprising to me is that modern dentists are highly kitted for
> > > > > > CNC-ing very hard ceramic materials at high precision.
> > > > > >
> > > > > > > > > > >
> > > > > But, small "tooth sized" pieces - how big is your crystal.
> > > > >
> > > > > > > > >
> > > > Well, they appearantly make a mouth-full at a time, so that is
> > > > covered...
> > > >
> > > > I don't think the dentist machines are precise enough though,
> > > > as I understood it, the state-of-the-art stuff has built in
> > > > laser-interferrometers etc.
> > > >
> > > > --
> > > > Poul-Henning Kamp | UNIX since Zilog Zeus 3.20
> > > > phk at FreeBSD.ORG mailto:phk at FreeBSD.ORG | TCP/IP since RFC 956
> > > > FreeBSD committer | BSD since 4.3-tahoe
> > > > Never attribute to malice what can adequately be explained by incompetence.
> > > >
> > > > _______________________________________________
> > > > time-nuts mailing list -- time-nuts at febo.com mailto:time-nuts at febo.com
> > > > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > > > and follow the instructions there.
> > > >
> > > > > > >
> > > _______________________________________________
> > > time-nuts mailing list -- time-nuts at febo.com mailto:time-nuts at febo.com
> > > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> > > and follow the instructions there.
> > >
> > > > >
> > >
>
More information about the time-nuts
mailing list