[time-nuts] Austron 2100F
paul swed
paulswedb at gmail.com
Sat Oct 23 01:58:00 UTC 2010
Bert always amazing hope you are well.
Regards
Paul.
On Fri, Oct 22, 2010 at 6:02 PM, <EWKehren at aol.com> wrote:
> Send me a picture direct to my email. I may have one. Bert Kehren
>
>
> In a message dated 10/22/2010 6:01:13 P.M. Eastern Daylight Time, as
> magal at fc.up.pt writes:
>
> With an outboard +/- 12 Volt power source my 2100F is now working fine.
> A new replacement package is therefore desperately needed.
>
> Best regards,
> Antonio
> CT1TE
>
> Quoting asmagal at fc.up.pt:
>
> > Dear All,
> >
> > Diving into the hardware, I found the DC-DC +5 to +/-12 V Power Source
> > defective. There may be something more but that is serious enough.
> >
> > Thank you for your kind attention and help.
> >
> > Antonio
> > CT1TE
> >
> > Quoting paul swed <paulswedb at gmail.com>:
> >
> >> Thats what I was thinking also on the reference and emailed back to the
> >> group.
> >> I believe over time that internal switch to select 1,5,10 mc can get a
> bit
> >> touchy.
> >> If a operating reference is connected and checked to be correct toggle
> the
> >> switch a few times to clean its contacts. It gets lonely sitting in
> there by
> >> itself for years. ;-)
> >> Regards
> >> Paul.
> >>
> >> On Fri, Oct 22, 2010 at 8:12 AM, Chuck Harris <cfharris at erols.com>
> wrote:
> >>
> >>> Hi Antonio,
> >>>
> >>> Ok. I just wanted to be sure that it was still up in Europe. Canada
> >>> dropped their chains 3 months earlier than they said they would. And
> >>> since Loran-C is no longer usable world wide, I figure Europe will be
> >>> dropping their chain soon.
> >>>
> >>> The error indication you have described tells me that you have no
> >>> reference oscillator. This could be for a couple of reasons:
> >>>
> >>> 1) you have no frequency standard connected to your 2100F
> >>> 2) the switch, labeled 1-5-10, on the board stack visible when you
> hinge
> >>> open the front panel is set incorrectly for your external frequency
> >>> standard.
> >>> 3) Your 2100F is broken.
> >>>
> >>> -Chuck Harris
> >>>
> >>> asmagal at fc.up.pt wrote:
> >>>
> >>>> Chuck,
> >>>>
> >>>> I am in Portugal, currently receiving the European
> >>>> 6731 LESSAY Chain.
> >>>>
> >>>> Best regards,
> >>>> Antonio
> >>>> CT1TE
> >>>>
> >>>> Quoting Chuck Harris <cfharris at erols.com>:
> >>>>
> >>>> Are you sure that your Loran chain is still up? In the US and
> >>>>> Canada, Loran has been decommissioned.
> >>>>>
> >>>>
> >>> _______________________________________________
> >>> time-nuts mailing list -- time-nuts at febo.com
> >>> To unsubscribe, go to
> >>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> >>> and follow the instructions there.
> >>>
> >> _______________________________________________
> >> time-nuts mailing list -- time-nuts at febo.com
> >> To unsubscribe, go to
> >> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> >> and follow the instructions there.
> >>
>
>
>
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to
> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
>
More information about the time-nuts
mailing list