[time-nuts] End-of-Range: Oscilloquartz OCXO 8600-3
Bob kb8tq
kb8tq at n1k.org
Fri Dec 8 16:26:29 EST 2017
Hi
It might be, if it is then an upper turn in the 80C range is not all that crazy.
Bob
> On Dec 8, 2017, at 4:24 PM, Angus <not.again at btinternet.com> wrote:
>
>
> That near the end of the temperature range the direction could also
> give a good indication - assuming that there is only one problem...
>
> I think the 8600-3 is still an AT - the 8607 is SC.
>
> Angus.
>
>
> On Fri, 8 Dec 2017 15:40:08 -0500, you wrote:
>
>> Hi
>>
>> One basic question - Is the frequency high or low?
>>
>> Assuming its an SC and on the lower turn, frequency low is possible
>> with an off temperature oven. Frequency high is unlikely unless its *way*
>> off temperature. How far off turn gives you how much delta F depends on
>> the inflection temperature of the crystal. It matters if its a true SCor a
>> modified SC
> .. If it is a true SC and running at 80C, thats about 10 degrees
>> below inflection. There will not be a lot of frequency change in that case.
>>
>> Many (but not all) modern crystal processes tend to age positive. If that is the
>> case on these parts, a frequency high is the likely outcome of age out of range.
>> Even with a process that has a known tendency, only about 70% of them go
>> that direction over long periods of time. Its not a perfect thing
> .
>>
>> Bob
>>
>>> On Dec 8, 2017, at 2:34 PM, Angus <not.again at btinternet.com> wrote:
>>>
>>>
>>> The 8601 that I have was about 2 deg C off turnover when I got it, but
>>> I can't remember what sort or frequency error that caused. The
>>> temperature coefficient was terrible with that error.
>>>
>>> Angus.
>>>
>>>
>>> On Fri, 8 Dec 2017 13:05:14 +0000 (UTC), you wrote:
>>>
>>>>
>>>> Gentlemen,
>>>> We have an Oscilloquartz OCXO 8600-3that cannot any longer be adjusted into 5,000,000 Hz.It is about 1 Hz out of 5 MHz and turning coarse/fineadjustment potentiometers cannot bring the frequencyinto its specification.
>>>> Oven temperature is about + 80C accordingto the thermistor and the operating voltageis at 24 VDC.
>>>> Have Googled but the only thing that turns upis datasheets w/o any details.
>>>> Before I take it apart and start lookingfor obviously broken components, isthere anyone that has a CLIP on this unit?
>>>> 73
>>>>
>>>> Ulf Kylenfall - SM6GXV
>>>> _______________________________________________
>>>> time-nuts mailing list -- time-nuts at febo.com
>>>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>>> and follow the instructions there.
>>> _______________________________________________
>>> time-nuts mailing list -- time-nuts at febo.com
>>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>>> and follow the instructions there.
>>
>> _______________________________________________
>> time-nuts mailing list -- time-nuts at febo.com
>> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
>> and follow the instructions there.
> _______________________________________________
> time-nuts mailing list -- time-nuts at febo.com
> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
> and follow the instructions there.
More information about the time-nuts
mailing list